THREE POINT BEND TEST FIXTURES

The flexure fixture allows a variety of flexural and fracture toughness bond tests to be performed, including determination of flexural modulus, flexural strength and flexural yield strength. Easy to install, the 3-point fixture can be modified with an optional conversion kit to provide a 4-point bending conversion. Lower anvils are adjustable to accommodate specimens of different spans. Deflection of the specimen can be measured either through crosshead displacement, or for more precise measurement you can use a mid-span direct measurement plunger with a clip-on extensometer.
Request a Quote
Catalog no. 2810-400

Principle of Operation
The specimen is supported on two precision machined anvils of a defined radius. The force is applied either centrally (3-point) or at a defined distance either side of the center (4- point). The support beam is graduated lengthways in metric units for accurate positioning of the anvils, equally spaced to the center line.
Application Range
Type of loading: Static flexure, cyclic flexure tests
Specimen material: Plastics, metals, alloys, composites, ceramics and other materials
Specimen shapes: Strip, bar, components
Common standards: ASTM D790, ISO 178
Features
- Rated capacity 5 kN (500 kgf, 1,125 lbf)
- 3-point flexure fixture with an optional conversion kit for 4-point loading
- Conforms to ISO, ASTM, DIN, and many other standards
- Fully adjustable span distance to suit a wide range of specimen sizes
- Adjustable stops for specimen widths up to 50 mm (2 in) for precise alignment
- Optional deflectometer plunger assembly
- Rugged design for minimum maintenance
- Temperature range: -100 to +350°C (-148 to +660°F)

Maximum Capacity | Adjustable Span Distance | Catalog no. | Specifications |
---|---|---|---|
5 kN | 10 - 200 mm | 2810-400 | View Full Specifications |
For Testing Plastics, Metals, Alloys, Composites, Microelectronics, and Components

100 kN Flexure Fixture
Catalog no. 2810-182
The 100 kN flexure fixture can perform 3-point flex / bend tests on specimens with a maximum width of 50 mm. A 4-point bend conversion kit is available. Lower span adjustable from 30 - 250 mm.
Learn More

250 kN Flexure Fixture
Catalog no. 2810-206
The 250 kN flexure fixture can perform 3-point flex / bend tests on specimens with a maximum width of 100 mm. A 4-point bend conversion kit is available. Lower span adjustable from 10 - 600 mm.
Learn More

100 kN Guided-Bend/Weld
Bend Test Fixture
Catalog no. W-6810
Adjustable span for "U" bend tests of plane plate or welded flat specimens. Fixture consists of a t-slot base with adjustable span supports (0 - 254 mm) supported by two tie rods. Maximum specimen width up to 76 mm.
Learn More

200 kN Cold Bend Testing Fixture for Steel Rebar
Catalog no. W-6812
Cold bend testing fixture for bend testing of steel reinforcement bars in general accordance with specifications; ASTM A615, A706, A996A, & BS4449. Maximum specimen diameter up to 76 mm. Support span adjustable from 0 - 480 mm.
Learn More

100 N Micro Flexure Fixture
for Microelectronics
Catalog no. 2810-410, 2810-411
Used for bend or flexure testing of miniature components and specimen typically found in microelectronic applications, the micro-bend fixture supports the specimen on two lower anvils and the load is applied by a single or optional dual upper anvil.
Learn More

2 kN Mini Flexure Fixture
for Miniature Components
Catalog no. 2810-412, 2810-413
The mini flexure fixture is designed for three-point bend or flexure testing of smaller components and specimens, where the specimen is supported on two lower anvils and the load is applied by a single or optional dual upper anvil.
Learn More